CISCO MAC ADDRESS TABLEHISTORY SOFTWARE
CISCO MAC ADDRESS TABLEHISTORY SERIES

This command was integrated into Cisco IOS Release 12.2(33)SRA. Support for this command on the Supervisor Engine 2 was extended to Release 12.2(17d)SXB. Add the ip keyword to the list of valid protocol names.Add the vlan vlan and cos value keywords and arguments.Support for this command was introduced on the Supervisor Engine 720. Global configuration (config) Command History Release Name of the ACL to which the entry belongs. No mac access-list extended name Syntax Description To remove MAC ACLs, use the no form of this command. To create an extended MAC access control list (ACL) and define its access control entries (ACEs), use the mac access-list extended command in global configuration mode. The following example applies MAC ACL 101 on incoming traffic received on Gigabit Ethernet interface 0: Router> enable Router# configure terminal Router(config)# interface gigabitethernet 0 Router(config-if)# mac access-group 101 in Related Commands CommandД¬onfigures an IP access list to be used for packets transmitted from the asynchronous host.Дisplays the ACL configuration on a Layer 2 interface.Дisplays the contents of one or all MAC ACLs. Note The mac access-group command is supported on a VLAN subinterface only if a VLAN is already configured on the subinterface.

CISCO MAC ADDRESS TABLEHISTORY SERIES

On Catalyst 6500 series switches, this command is supported on Layer 2 ports only. If the specified MAC ACL does not exist on the interface or subinterface, all packets are passed.

CISCO MAC ADDRESS TABLEHISTORY SOFTWARE

If the access list denies the address, the software discards the packet and returns an Internet Control Message Protocol (ICMP) host unreachable message. If the MAC access list permits the address, the software continues to process the packet. After a networking device receives a packet, the Cisco IOS software checks the source MAC address of the Gigabit Ethernet, 802.1Q VLAN, or 802.1Q-in-Q packet against the access list.

MAC ACLs are applied on incoming traffic on Gigabit Ethernet interfaces and VLAN subinterfaces. This command was integrated into Cisco IOS Release 12.2(33)SXH. This command was introduced on the Cisco 12000 series Internet router. Subinterface configuration (config-subif) Command History Release No access list is applied to the interface or subinterface. This is a decimal number from 700 to 799. Number of a MAC ACL to apply to an interface or subinterface (as specified by a access-list (MAC) command). No mac access-group access-list-number in Syntax Description To remove a MAC ACL, use the no form of this command. To use a MAC access control list (ACL) to control the reception of incoming traffic on a Gigabit Ethernet interface, an 802.1Q VLAN subinterface, an 802.1Q-in-Q stacked VLAN subinterface, use the mac access-group command in interface or subinterface configuration mode.

pl atform port-channel local-significance.

mls rp ip multicast management-interface.

mac-address-table notification threshold.

mac-address-table notification mac-move.

Client usage data after changing Client tracking mode. Client usage data before changing Client tracking mode.ДЇigure 2. This can be verified on the Monitor > Clients page.ДЇigure 1. Click Confirm againВ at the top of the page. Select the option that was originally chosen, as noted in step 3.Д©. For example, if Track by MAC addressВ is selected, chose Track by IP addressВ and if Track by IP addressВ is selected, choose Track by MAC address.Д§. Change the Client tracking modeВ by selecting the choice that is not currently selected. The possible options are Track by MAC addressВ and Track by IP address.Д¤. Take note of the current setting under Client Tracking. To clear the client usage data please follow the steps below.ДЎ.В Log into yourВ DashboardВ account and select your MX network from the NetworkВ drop down.Дў.В Navigate to Security Appliance > Configure > Addressing & VLANs.ДЈ. The MX Security Appliance will clear its client usage data on Monitor > ClientsВ whenever the Client Tracking mode is changed.

Cisco mac address tablehistory